![]() ![]() By default, the "GE0" interface isĬisco UCS E-Series Servers and the Cisco UCS E-Series Network Computeįor initial login, use admin as the default user name, and Admin123# as the default password. The backplane has one internal WAN interface (GE0) to establishĬonnection with the Cisco UCS-E server. The WAN traffic comesįrom the ISR WAN ports, and goes through the backplane to the Cisco UCS-E ![]() TheyĪre not externally available on the Cisco UCS E server. By default, the hostnameĪ WAN bridge (wan-br)- The physical WAN ports are on the Cisco ISR module. Outbound traffic are associated with the LAN bridge. The NFVIS host is configured on the LAN bridge. LAN bridge (lan-br)-The default static management IP address (192.168.1.1) for The device are associated with the LAN bridge.įor more details about the initial setup, see the Installing the Server chapter in the Cisco UCS C220 M4 Server Installation and Service Guide or Cisco Cloud Services Platform 2100 Hardware Installation Guide.Ĭonfiguration on the Cisco UCS E-Series ServersĬonfiguration with a Cisco UCS E-Series Server ![]() Port on the device is associated with the WAN bridge. By default, the hostname is set to "nfvis".Ī WAN network (wan-net) and a WAN bridge (wan-br)-This is created with the "eth0" port, and is configured to enable the DHCP LAN port can be used to access the default static IP address. All other ports for inbound and outbound traffic are associated with the LAN bridge. You can configureĪ LAN network (lan-net) and a LAN bridge (lan-br)-The default static management IP address (192.168.1.1) for the NFVIS host Default Network Configuration with Cisco UCS C220 M4 and Cisco CSP 2100Īnd bridges are created by default, and cannot be deleted. The following diagram illustrates the default networkįigure 3. Networks in Cisco Enterprise NFVIS allows inbound and outbound traffic and VMs Wan2-net and wan2-br are the default configurations for ENCS 5400 and ENCS 5100.ĭefault System Configuration on the Cisco UCS C220 M4 Server and Cisco CSP 2100 You can configure more as required.Ī LAN network (lan-net) and a LAN bridge (lan-br)Ī WAN network (wan-net) and a WAN bridge (wan-br) The following networks and bridges are automatically configured. This internal subnet will be isolated so that users can use this for NFVIS management. A user should not use this IP subnet on the NFVIS management network. Not be used on the external switch ports and for virtual machines in the LAN ports". Reserved VLANs in the LAN network on the ENCS 5400 platform-The VLAN range 2350-2449 is reserved for internal use and should Segment Layer 2 bridge domain where only the specific VLAN traffic is allowed. Multiple VMs can use the same LAN port for local connectivity. The default management IP address (192.168.1.1)įor the NFVIS host is configured on the management port. Machine to provide virtual network interfaces by defining a range of MAC addresses. WAN port-You can use one of the dual media Ethernet ports (wan-br and wan2-br) for DHCP connection.īridges-They form a Layer 2 domain between virtual network interface controllers (vNICs) of VMs. Physical Gigabit Ethernet ports for inbound and outbound traffic. ![]() Default Network Configuration of Cisco Enterprise NFVIS with the Cisco ENCS 5100 Default Network Configuration of Cisco Enterprise NFVIS with the Cisco ENCS 5400įigure 2. The diagram below illustrates the default network configuration of Cisco Enterprise NFVIS with the Cisco ENCS. Backup and Restore NFVIS and VM Configurationsĭefault System Configuration on the Cisco ENCS.Enhancements to DPDK Support in NFVIS 3.12.x.Enabling or Disabling the Portal Access.Setting the System Time Manually or With NTP.Configuring Your Banner and Message of the Day.Port 22222 and Management Interface ACL.Configuring Minimum Length for Passwords.Configuring VLAN for NFVIS Management Traffic.Default System Configuration on the Cisco UCS E-Series Servers.Default System Configuration on the Cisco UCS C220 M4 Server and Cisco CSP 2100.Default System Configuration on the Cisco ENCS. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |